home *** CD-ROM | disk | FTP | other *** search
/ Software Vault: The Gold Collection / Software Vault - The Gold Collection (American Databankers) (1993).ISO / cdr11 / intmemry.zip / MEMO1328.TXT < prev    next >
Text File  |  1992-08-13  |  11KB  |  272 lines

  1.  ╔═════════════════════════════════════════════════════════════════════════╗
  2.  ║                                                                         ║
  3.  ║      Classic Above Board Disk Controller Board Compatibility            ║
  4.  ║                                                                         ║
  5.  ╚═════════════════════════════════════════════════════════════════════════╝
  6.  
  7.  ALWAYS TECHNOLOGIES IN2000 SCSI CONTROLLER
  8.  
  9.      *CUSTOMER REPORT* of compatibility with Above Boards and Matched Memory
  10.      Classic.
  11.  
  12.      Tech Notes:  This controller uses reserved memory address C0000-CBFFF.
  13.      The report indicated that it was necessary to change the SCSI
  14.      controller I/O address from 220 to 110 or the system wouldn't boot with
  15.      the controller and the Intel memory board installed at the same time.
  16.  
  17.  BERNOULLI BOX INTERFACE BOARD BY IOMEGA
  18.  
  19.  BERNOULLI BOX INTERFACE BOARD BY IOMEGA
  20.  
  21.      Compatible with Above Boards and Matched Memory Classic.
  22.  
  23.      TROUBLESHOOTING:  Try swapping the order of the Bernoulli and EMM.SYS
  24.      device drivers.  If you are using the QUIKMEM2 RAM disk software, be
  25.      sure the Bernoulli device driver is loaded BEFORE QUIKMEM2.
  26.  
  27.      Check to be sure you have the correct adapter board for your machine
  28.      type:
  29.      >> The PC3 or PC3B boards are for PC and XT systems.
  30.      >> The PC2 or COMBO boards are for AT systems.
  31.  
  32.      In some cases the PC3 or PC3B boards will work in AT systems until you
  33.      load the bus, but remember they are using an adapter board that is not
  34.      designed for an AT system.  So if the Intel memory board works without
  35.      the Bernoulli board installed, they'll need to replace the Bernoulli
  36.      board.
  37.  
  38.      ROM ADDRESS:  The Bernoulli board is configurable from C0000 to E0000
  39.      with jumpers on the board.  The 8K ROM is needed only if booting from
  40.      the Bernoulli.
  41.  
  42.  ASC-88 SCSI ADAPTER
  43.  
  44.      ASC-88 SCSI Adapter by Advanced Storage Concepts
  45.      Compatible with Above Boards and Matched Memory Classic.  Has switch
  46.      settings for reserved memory addresses.  The factory default setting is
  47.      CC00.  The following jumper settings are as listed from their manual,
  48.      Appendix B:
  49.  
  50.      A16  A15  A14  ADDRESS
  51.       0    0    0 =  C000
  52.       0    0    1 =  C400
  53.       0    1    0 =  C800
  54.       0    1    1 =  CC00 factory default setting
  55.       1    0    0 =  D000
  56.       1    0    1 =  D400
  57.       1    1    0 =  D800
  58.       1    1    1 =  DC00
  59.  
  60.      If you are setting the Intel memory board for expanded memory, use the
  61.      EXPF or EXPL parameters to relocate the expanded memory page frame
  62.      before or after the ASC memory address.
  63.  
  64.  CUMULUS SILHOUETTE EXTERNAL HARD DRIVE ADAPTER
  65.  
  66.      *CUSTOMER REPORT* of compatibility with current Above Boards, Matched
  67.      Memory Classic, and the discontinued Above Board 286 and PS/286.
  68.  
  69.      Tech Note: This board may use I/0 address 208.  If there's a conflict,
  70.      remove the Cumulus board, and change the Intel memory board I/0 address
  71.      to something other than 208.  Then re-install the Cumulus board.
  72.  
  73.  COPYII PC DELUXE BY CENTRAL POINT
  74.  
  75.      *CUSTOMER REPORTS* of compatibility with Above Boards and Matched
  76.      Memory Classic.
  77.  
  78.      Tech Notes: Default I/O port address for the CopyII PC Deluxe board
  79.      conflicts with Above Boards.  Jumpers for Deluxe:
  80.  
  81.      J6 has two jumpers:       LEFT   RIGHT  I/O ADDRESS
  82.                                ----   -----  -----------
  83.                                UP     UP     268h-26Fh  default
  84.                                DOWN   DOWN   3E8h-3EFh
  85.                                UP     DOWN   368h-36Fh
  86.                                DOWN   UP     2E8h-2EFh
  87.  
  88.      J7 controls DMA port:     UP   = channel 1  default
  89.                                DOWN = channel 3
  90.  
  91.  DATAMATIC SCSI HARD DISK CONTROLLER
  92.  
  93.      Compatible with Above Boards and Matched Memory Classic.
  94.  
  95.      Tech Notes:  The factory default I/O address is 330.  Alternate choices
  96.      are 320, 328, 330, and 338.  The factory default for ROM address is set
  97.      to D800 using 16K.  Alternate ROM addresses are C800, CC00, D000, and
  98.      D800 configured by jumpers on the board.
  99.  
  100.  EXPANZ!
  101.  
  102.      Disk compression product, a half-length AT-bus board that contains an
  103.      ASYC with a disk compression algorithm.  The algorithm works like
  104.      PKZip; however, it appears to be a more efficient algorithm.
  105.  
  106.      This product uses a 16K reserved page frame.  The board can be set to
  107.      the following addresses:
  108.  
  109.          CC00 (default)  DC00       EC00
  110.          C800            D800       E800
  111.          C000            D400       E400
  112.                          D000       E000
  113.  
  114.      If the customer is on a system that permits access to the E000 range
  115.      (XTs), set the "Expanz!" board to a 16K boundary in this range.  If the
  116.      user is on a system that does not decode E000 (ATs), then EMM will
  117.      require a page frame parameter.
  118.  
  119.  FUTURE DOMAINS SCSI CONTROLLER
  120.  
  121.      *CUSTOMER REPORTS* of LIMITED COMPATIBILITY with Above Boards and
  122.      Matched Memory Classic depending on the version of the SCSI controller.
  123.  
  124.      Symptom:  With an Intel memory board in the system the hard drive would
  125.      time out.  Removing the EMM.SYS driver DID NOT HELP.  The SCSI board
  126.      had -02 on the assembly number on the front of the board.
  127.  
  128.      Solution:  Customer tried the newer version of the SCSI board, -03, and
  129.      it worked fine.
  130.  
  131.  PLUS HARDCARD IN THE IBM AT
  132.  
  133.      *CUSTOMER REPORTS* of compatibility with Above Boards and Matched
  134.      Memory Classic.
  135.  
  136.      NOTE:  The Plus Hardcard BIOS ver 4.2 is INCOMPATIBLE with the 6MHz IBM
  137.      AT BIOS dated 1-10-84.  The solution is to replace the BIOS with a
  138.      later revision of the IBM BIOS.
  139.  
  140.  IBM 5.25 EXTERNAL FLOPPY CTRL AND LOTUS 2.0
  141.  
  142.      *CUSTOMER REPORT* of compatibility with Above Boards and Matched Memory
  143.      Classic.
  144.  
  145.      One customer reported that his IBM Model 30/286 locked up whenever he
  146.      accessed the 5.25 drive in Lotus 2.0.  The problem disappeared when he
  147.      switched to Lotus ver 2.01.
  148.  
  149.  KODAK 6.6MB FLOPPY CONTROLLER
  150.  
  151.      *CUSTOMER REPORT* of compatibility with Above Boards and Matched Memory
  152.      Classic.  This controller has a ROM that uses memory from D000h -
  153.      D1FFFh or D200h - D3FFFh.
  154.  
  155.  KONAN DISK CONTROLLER
  156.  
  157.      *CUSTOMER REPORT* of compatibility with current Above Boards and
  158.      Matched Memory Classic.
  159.  
  160.      Tech Note:  This is a 16-bit disk controller board with 16K ROM at a
  161.      switchable address (C000, C800, CC00, D000, D400, D800, DC00).  One
  162.      customer reported his AT-Clone wouldn't boot when the discontinued
  163.      Above Board 286 was installed with this board.  Upgrading to the Above
  164.      Board Plus allowed it to work with both boards in 16-bit mode.
  165.  
  166.      Konan ph: 602-345-1300
  167.  
  168.  LCS 6610F FLOPPY CONTROLLER
  169.  
  170.      *CUSTOMER REPORT* of INCOMPATIBILITY with Above Boards in one computer.
  171.      Long Shine Computers XT hangs on boot with this board and an Above
  172.      Board, even when the EMM.SYS driver is not installed.  Customer
  173.      switched to a Western Digital disk controller using the LCS BIOS and it
  174.      worked.
  175.  
  176.      LCS controller handles two internal floppies, has a BIOS that can
  177.      reside at either CC000 or CA000, I/O ranges 370-37F.
  178.  
  179.  NEC T-128 SCSI HOST ADAPTER
  180.  
  181.      *CUSTOMER REPORT* of compatibility with current Above Boards and
  182.      Matched Memory Classic.  This adapter has 8Kb of ROM and its location
  183.      is configured by switches on the card.
  184.  
  185.      AVAILABLE ADDRESSES:  C800
  186.                            CC00
  187.                            D800
  188.                            DC00
  189.  
  190.  PLUS PASSPORT SYSTEM - CLASSIC BUS
  191.  
  192.      *CUSTOMER REPORT* of compatibility with Above Boards and Matched Memory
  193.      Classic.
  194.  
  195.      Tech Notes:  This is a removable 20 or 40Mb hard disk system that
  196.      connects to an adapter board in the computer.  System is available for
  197.      both Classic bus and Micro-channel machines.  Has a 16K read-ahead
  198.      buffer.
  199.  
  200.      PC Adapter: (selecting the controller number determines other values)
  201.  
  202.      CONTROLLER      BIOS        I/O
  203.        NUMBER       ADDRESS     ADDRESS
  204.          0           C800      320H-323H
  205.          1           CA00      324H-327H
  206.          2           CC00      328H-32BH
  207.          3           CE00      32CH-32FH
  208.  
  209.      Uses DMA channel 3 and IRQ 5
  210.  
  211.      Instructions for changing jumper settings are located on page 7 of the
  212.      Adapter Installation Guide
  213.  
  214.  SEAGATE ST11M/ST11R ST412 INTERFACE CONTROLLER
  215.  
  216.      **FIELD REPORTS** of compatibility with current Above Boards.
  217.  
  218.      Tech Notes: This is an 8-bit controller board that can configure its
  219.      reserved memory usage via jumper block W1 (located just about in the
  220.      middle of the board).  The jumper settings are:
  221.  
  222.             ╒═════════════════╤════════════════╤═════════════╕
  223.             │ Jumper Setting  │ BIOS Address   │ Port Address│
  224.             ╞═════════════════╪════════════════╪═════════════╡
  225.             │ No Jumpers      │ C8000H(default)│ 320H - 323H │
  226.             ├─────────────────┼────────────────┼─────────────┤
  227.             │ Pins A-B jumped │ D0000H         │ 324H - 327H │
  228.             ├─────────────────┼────────────────┼─────────────┤
  229.             │ Pins A-B jumped │ D8000H         │ 328H - 32BH │
  230.             ├─────────────────┼────────────────┼─────────────┤
  231.             │ A-B & C-D jumped│ E0000H *       │ 32CH - 32FH │
  232.             ╘═════════════════╧════════════════╧═════════════╛
  233.             *Do not use in AT-Class systems!
  234.  
  235.  TALLGRASS HARD DISK MODEL TG-6180
  236.  
  237.      Compatible with Above Boards and the Matched Memory Classic.
  238.  
  239.      Tech notes: If the customer is having problems installing our drivers
  240.      with the INSTALL program we used to ship, have them do a manual
  241.      software installation or use the SOFTSET program (SOFTSET replaced
  242.      INSTALL quite a long time ago).
  243.  
  244.  TECHMAR QUICK 60 TAPE BACK-UP
  245.  
  246.      *Field report* of compatibility with Above Boards.
  247.  
  248.      Tech Notes: This tape back-up board has a ROM at C000, don't know
  249.      ending address.
  250.  
  251.  WESTERN DIGITAL 1002A-FOX???
  252.  
  253.      *FIELD REPORT* of compatibility with Above Boards.
  254.      WD1002A-FOX001     2 floppy controller for AT (No ROM)
  255.      WD1002A-FOX002     4 floppy controller for AT (No ROM)
  256.      WD1002A-FOX003     2 floppy controller for XT (ROM)
  257.      WD1002A-FOX004     4 floppy controller for XT (ROM)
  258.  
  259.      These controllers will run anything from a 360k to a 1.44m floppy,
  260.      hence the ROM on the XT controllers.  The ROM default address is CC00-
  261.      CDFF.  It can be move to CE00- CFFF or in the high E000 range (same two
  262.      offsets.)
  263.  
  264.  WESTERN DIGITAL WD1007/WA2
  265.  
  266.      Can cause system to not boot after installing AB, due to extreme length
  267.      of I/O read & I/O write lines on the controller board.
  268.  
  269.  
  270. ══════════════════════════════════════════════════════════════════════════════
  271. End of file                 Intel FaxBack # 1328          August 13,1992
  272.